How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security system that shields your car from key cloning and hacking. It stops the engine from starting until a PIN code has been entered. This can be as long as 20 characters.
It is not detected by thieves who don't expect this extra layer of security. Certain systems also come with an application that lets owners disarm the immobiliser in case they forget their PIN code, or to use a service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is a cutting-edge security system, can be incorporated directly into the ECU of your vehicle. It provides a discreet protection against thieves. It is highly efficient and user-friendly. This makes it a valuable asset to your vehicle's arsenal of security. Like all anti-theft devices, it's not foolproof, and requires regular maintenance to function properly. Fortunately, this guide can assist you in getting the most value from the Ghost 2 Immobiliser.
CAN (Controller Area Network) is a robust serial network that allows microcontrollers to communicate with each other over short distances without the necessity of central control units. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It offers many advantages including low cost and simple use.
The CAN protocol is utilized in a majority of modern cars to communicate with the engine management system, steering control module, air conditioning controls, and more. It also carries sensor information like speed sensors and other inputs, to regulate the various features of the car. The CAN bus is used to monitor these diverse components, and can prevent the vehicle from starting if they're in a dangerous state.
While the CAN bus can be used for a variety of purposes, it's important to know how it functions and how it's secured. The CAN bus is a great way to add new features to your vehicle, but it's also essential to secure it from threats such as hackers and other. Installing a firewall and monitoring your CAN-bus with software is the best method to accomplish this.
Ghost2's secluded control unit is hidden inside the car's wiring harness or dashboard, removing the possibility of a thief physically tampering with it. It is also impossible to reset the PIN or emergency code without access to the vehicle.
You can activate Transport Mode If you need to surrender your vehicle for service, valet parking or any other reason. This feature disables both the keyfob and the ignition functions of the Ghost immobiliser. It will only reactivate when the vehicle has reached 31 mph for a period of 15 minutes.
How do you create a PIN code
The Ghost immobiliser guards your vehicle from thieves. The most advanced technology utilizes an PIN code to disable the engine and stop it from starting if you do not have the proper code or an authorized fob or mobile device. The system's discrete design is unnoticeable and also provides unbeatable security against theft. The system is TASSA certified and could save you substantial amounts on your car insurance.
During the installation, Ghost enters a "learning mode" to record the sequence of buttons that are pressed in order to generate your unique pin codes. Once the pin code is created, the installer will then guide you through the steps to activate the system. Once activated it will Ghost system will shut down the starter motor of your vehicle until a valid PIN has been entered or the vehicle is switched to transport mode. This makes it extremely difficult for thieves or cloners who want to hack or clone your vehicle's starter system.
It's easy to set up a Ghost immobiliser, however, you must follow the specific instructions provided in the user's guide to ensure that it is operating properly. Multimeters and basic hand tools can be used to verify electrical values. Insulation tape as well as heat shrink tubing and cable ties are a good option to protect exposed wiring. Test the system on a regular basis to identify any issues that could be.
After the installation is completed, it is important to conduct a final test of the system before turning on your vehicle's ignition. The Ghost immobiliser will arm itself after a period of 3 to 30 seconds, depending on your vehicle's model. The system is also fitted with a Service/Valet Mode which allows you to temporarily remove the system for servicing or valet parking.
Idealy, the immobiliser will be hidden under the dashboard or on the steering wheel. Use a small amount of tape or paint on the CAN H and L wires to make them easier to locate when testing. Additionally the CAN H and CAN L wires must be connected to a source of power that is able to provide continuous 12V. ghost ii immobiliser is also crucial to check the connections again after testing, as misidentifying these wires can cause the system to malfunction.
The system must be activated
A ghost immobiliser prevents the car from starting unless you press a number of buttons on the vehicle, usually on the steering wheel or door panel, or the central console. The sequence can be altered by the user if needed. Once the system is activated it cannot be deactivated by thieves, making it a good option for anyone looking to safeguard their vehicle from theft.
The system is designed not to be detectable by modern diagnostic and code-grabbing technologies. It doesn't emit radio frequency either, making it even more difficult for thieves detect.
If the device is detected, it will stop the engine from running and sound a loud alarm to deter thieves. The device can be used to track the location of the vehicle and help police track it down when it is stolen.
Contact Car Specalist Customs for a quote or to discuss your options if you're interested in Ghost immobiliser. We are fully certified to install a ghost immobiliser on your vehicle and will make sure it is hidden in a hard-to-reach area. We can also provide additional security measures such as the wheel lock and kill switch to protect your vehicle from thieves.
Disarming the System
It is essential to know how to disable the Ghost immobiliser if it is fitted to your car. This will help you in the case that you lock your keys in the car or when your battery fails. The system utilizes an individual PIN code that only you know, so the immobiliser will not be able to start your car without entering this code. The simplest method to enter the code is to press a set of buttons on your dashboard or the steering wheel. This is a far simpler method than using the key fob, and it also keeps anyone from copying your remote.
Ghost2 isn't intrusive unlike some aftermarket immobilisers which require cutting wires for installation. It also integrates with the CAN bus system of your vehicle in order to function. Its main feature is its ability bypass the engine without affecting your vehicle's normal functions, making it hard for thieves to use signal boosters or clone your car key. It doesn't emit radio frequency, so thieves are unable to detect it.
The Ghost system has a Transport Mode that allows you to temporarily disable security for certain situations such as service or transportation. This feature is useful for when you're loaning your vehicle to someone else without sharing your PIN number, or if your vehicle needs to be protected when you drive it. To activate the Transport Mode you need to press the service button 5 times within a period of 2 seconds. The Ghost system will confirm activation with 5 signal indicators.
When you're done, remember to save the emergency code in a secure location outside of your vehicle. If you ever find yourself locked out of your vehicle you can contact the company or technician who installed the system and they'll provide you with the code. If they are not able to contact you then you can attempt to contact an authorized dealer but this would require verification procedures and could result in additional charges.
Apart from the ease of this system, you can also depend on it to safeguard your vehicle from theft and help reduce the cost of insurance. Many insurance companies offer reduced rates or financial incentives to install this anti-theft system.